Fenix Spares & Accessories

This adaptor is designed to work with the Fenix ARE-C2 battery charger and enables you to use your Fenix battery charger in a vehicle that has a standard 12 volt vehicle power outlet.

The Fenix TK75 extended run-time kit features a body extender and battery carrier enabling your TK75 to hold an additional 4 x 18650 batteries (not included) therefore doubling the TK75's run-time. Several kits can be added to the TK75 (Fenix recommend a maximum of three), each kit adding an extra TK75's normal run-time.

This handy Fenix red filter turns your white light in to red light simply by pushing it on to the head of the torch to provide a friction fit. For use with the following models: LD10, LD11, LD12, LD20, LD22/LD22 2015, PD10, PD20, PD22, PD25, PD30, RC09 or any torch with a 21.5 mm head diameter.

These are accessories for Fenix torches which have outstanding filtration ability to create strong red/blue/green light. With high penetrability for fog and smoke, they can be used as a signal lamp, for hunting or to protect night vision as necessary. Uses a toughened ultra-clear glass lens with anti-reflective coating that provides heat resistance and maximum light penetrability.

These are accessories for Fenix torches which have outstanding filtration ability to create strong red/blue/green light. With high penetrability for fog and smoke, they can be used as a signal lamp, for hunting or to protect night vision as necessary. Uses a toughened ultra-clear glass lens with anti-reflective coating that provides heat resistance and maximum light penetrability.

These handy filter accessories are for the Fenix TK09/TK09 2016, TK11, TK12, TK15, TK16 and TK20R series torch and feature a high quality toughened glass lens with anti-reflective coating for maximum light transmission.
Please Note: Torch is not included.

The Fenix AOD-S diffuser is designed to fit a wide range of Fenix torches and converts your Fenix torch into a powerful and versatile 360 degree lantern and is compatible with the following models: P1D, P2D, PD10, PD20, PD22, PD30, PD31, PD32, PD35, L1, L1P, L2P, L1S, L2S, L1T, L2T, L1D, L2D, LD10, LD20, LD22, LD25, E20, E21, E25, E35.

The Fenix AOD-M diffuser is designed to fit a head diameter between 34 - 40 mm and converts your Fenix torch into a powerful and versatile 360 degree lantern and is compatible with the following models: LD41/LD41 2015, TK09 2016, TK10, TK11, TK12, TK15, TK15UE, TL15C, TK16, TK20, TK21, TK22, E40, E50, RC10, RC15, RC20, PD40

The Fenix Camping Lampshade is designed to transform your compact Fenix torch or head torch into a versatile camping lantern. Perfect for camping and hiking, enabling you to leave your larger lantern at home when weight is important, without compromising on performance. Fits 21.5 mm head diameter.

The Fenix AD502-N TK camping lampshade transforms your Fenix torch into a powerful camping light, serving as a versatile, multi-purpose lighting tool without the added weight and bulk of a separate lantern. Fits 34 mm head diameter.

Fenix traffic wands can convert your torch into a glowing red high-visibility wand. Designed for emergency situations and traffic control.

Fenix traffic wands can convert your torch into a glowing high-visibility wand. Designed for emergency situations and traffic control.

Fenix traffic wands can convert your torch into a glowing red high-visibility wand. Designed for emergency situations and traffic control.

The Fenix ALD-02 helmet clips consist of four plastic hooks that are designed to prevent the head band of a head torch from sliding off of a work helmet. The clips attach to the head band and then the clip hooks over the rim of the helmet to hold the head torch in place. The clip also has a small plastic loop on the front so that any wiring that runs from the head lamp to a rear battery pack can be tucked away.

The Fenix ALG-03 is design to mount the Fenix HL55 or HL60R to a helmet or hard hat. The head torch attachment plate permanently attaches to your helmet using the included TESA and 3M adhesive tape. Once the tape has been allowed to adhere to the helmet for 72 hours you can then insert your HL55 or HL60R head torch and easily remove when needed.

The Fenix AER-02 tactical remote pressure switch replaces the tail cap of your Fenix torch and provides a cable mounted pressure pad and switch. The noiseless pressure pad measures 30 mm long and provides momentary operation of your torch by applying slight finger pressure, once pressure is released the torch turns off.

The Fenix AER-03 tactical remote pressure switch replaces the tail cap of your Fenix torch and provides a cable mounted pressure pad and switch. The noiseless pressure pad measures 30 mm long and provides momentary operation of your torch by applying slight finger pressure, once pressure is released the torch turns off. A round switch activates constant illumination of your torch, great for night time navigation.

Fenix compatible models include: TK09, TK11, TK12, TK15, TK16, TK22, TK32, PD32, PD35, PD35 Tac etc.

The Fenix ALG-01 is a high quality gun mount for the Weaver/Picatinny type rail and fits a wide
range of Fenix torches.

A high quality mount for fixing your one inch diameter torch to a gun barrel of up to 18 mm diameter.

A quality torch mount which features a one inch mounting ring at both ends for fitting of a one inch bodied torch such as the Fenix TK11, TK15 or TK21 to a one inch bodied rifle scope.

The Fenix ALB-10 is a versatile quick release bike mount which enables the fitting of a torch to your bike handlebars. The mount can hold torches with a body diameter of 18-26 mm and fits on handlebars with a diameter of 22-35 mm. Horizontal adjustment of 30 degrees left or right is also possible.

An upgraded version of the hugely popular Twofish Lockblock mount, the cycleblock features heavy duty velcro retaining straps to securely fix torches up to C - cell size to your handlebars.

This is a spare holster for the following Fenix torch models: LD20 and LD22.

This is a spare holster for the following Fenix torch models: PD20 and PD22.

This is a spare holster for the following Fenix torch models: PD30.

This is a spare holster for the following Fenix torch models: PD35.

Fenix spare holster for the following models: TK10, TK11, TK12 and TK15.

The Fenix 360 degree The Fenix AB02 rotary clip is suitable for all Fenix LD, PD and 2 x CR123 / 1x 18650 powered TK series torches.

Please Note: A torch is not included with this item

This Fenix head torch storage case is designed for the HL/HM series of head torches and fits the Fenix HL10, HL12R, HL15, HL16, HL18R, HL23, HL26R, HL30, HL23R, HL35, HL40R, HL50, HL55, HL60R and HM50R.

A set of four Unilite helmet clips to fit on your head torch strap. These clips enable you to clip the head torch strap to your helmet and stop the straps slipping up the side of the helmet, a very useful item!

A set of 4 large helmet clips to fit on your head torch strap. These clips enable you to clip the head torch strap to your helmet and stop the straps slipping up the side of the helmet, a very useful item!