Olight Warrior Mini Rechargeable LED Torch
Olight Warrior Mini Rechargeable LED TorchOlight Warrior Mini Rechargeable LED TorchOlight Warrior Mini Rechargeable LED Torch
Olight Warrior Mini Rechargeable LED TorchOlight Warrior Mini Rechargeable LED TorchOlight Warrior Mini Rechargeable LED Torch

Olight Warrior Mini Rechargeable LED Torch

Availability:  10+ in stock
Brand:  Olight
Product Code:  OL1047-B
 
maximum allowance of 20 characters
£79.95

The Olight Warrior Mini is a perfect mix between the M2R Pro Warrior and the Baton Pro, offering an EDC carry friendly maximum output of 1500 lumens, before dropping down to 500 lumens after 4 minutes to prevent the LED from overheating.

Utilising a cool daylight white LED with a TIR optic lens, the Warrior Mini provides better light quality with a smooth and balanced beam profile. It features the rugged design and dual switches of the M2R Pro combined with the slim compact design and 18650 battery of the Baton Pro, making it the perfect everyday tactical carry.

The included Olight 18650 3500 mAh 10 A high discharge tailored lithium-ion battery is specially designed and only this battery can be charged within the torch. The battery is recharged inside the torch using the included MCC3 magnetic charging cable.

Simply connect the magnet to the base of the torch and plug the USB end into a computer or suitable adaptor. The light on the cable will go red to show charging is in progress and turn green once charging is complete, a full charge takes approximately 3 hours and 30 minutes when using a 5 V 1.5 A input, otherwise charging may be slower.

Featuring five brightness levels and strobe, the torch is turned on and off with a single press of the side mounted push button. Select the brightness level, with the torch turned on, by holding the switch to cycle through low, mid and high in turn, whilst the moonlight mode of 1 lumen can be accessed directly when the torch is off by pressing and holding down the switch, or a single press if it is the last used memorised mode.

Quickly double pressing the side switch will enter turbo mode and three quick presses with the light on will activate the strobe mode. The memory function will remember the last mode used for moonlight, low, mid and high. Turbo mode will be remembered as high mode.

The redesigned tactical tail switch provides stronger magnetism and allows for easier operation while wearing gloves due to the raised button, but without compromising accidental activation thanks to the three raised struts that not only prevent it easily turning on but also allow for tail stand capability. The tail switch will access constant with quick half or full presses, or momentary with a full or half press and hold.

The tactical tail switch is a quiet press button with minimal noise for tactical purposes and can be used in two modes; either configuration 1 or configuration 2. The torch default setting is configuration 1 and to switch to configuration 2 you deep press and hold the tail switch then single press the side switch. In Configuration 1 the tail switch will provide mid output with a half press or turbo output with a full press, while configuration 2 will provide turbo output with a half press or strobe with a full press.

A battery level indicator built into the side switch lets you know when the battery needs charging. A green light indicates above 60% power, a orange light indicates 10% - 60 % power a red light indicates 10% - 5% power and a red flashing light indicates less than 5% power and that the torch needs to be charged.

A handy lockout function prevents the torch from being accidentally activated and is accessed by pressing and holding the switch for 2 seconds to lock it (it will enter moonlight mode first and then lockout) and the same again will unlock it. The Baton Pro also features a dual purpose magnetic tail cap, so you can use it as a hands-free work light, and attach it securely to the included charging cable.

The innovative two way pocket clip makes it easy to carry the Warrior Mini on clothing, and what's more it comes supplied with a blue one attached to the black version, or a black pocket clip attached to the desert tan version for that contrast style.

Operational Modes

Turbo:
1500 lumens; 4 minutes run-time; 190 m beam range*
500 lumens; 3 hours, 25 minutes run-time
170 lumens; 55 minutes run-time

High:
500 lumens; 3 hours, 38 minutes run-time; 110 m beam range
170 lumens; 50 minutes run-time

Mid: 120 lumens; 18 hours run-time; 54 m beam range
Low: 15 lumens; 150 hours run-time; 18 m beam range
Moonlight Mode: 1 lumen; 45 days run-time

*The turbo and high setting will decrease to prevent the LED from overheating.

The above results are based on ANSI/NEMA FL1-2009 standard and are tested using the included battery.


Technical Details

Type: Professional hand-held LED torch
Operating Modes: Moonlight / Low / Mid / High / Turbo / Strobe
Luminous Flux: Up to 1500 lumens
Lamp Type: Cool daylight white LED
Lens: TIR reflector
Beam Range: Up to 190 m
Batteries Required: 1 x tailored 3500 mAh 10 A HDC 18650 lithium-ion (included)
Overall Length: 106.5 mm
Bezel Diameter: 23 mm
Weight: 105 grams (including battery)
Body Colour: Black or desert tan
Body Material: Constructed from 6061-T6 aluminium alloy
Body Finish: Type III hard-anodised
Switch Type: Side mounted and tactical tail switch
Other Technology: Magnetic base
Impact Resistance: 1.5 m
Environmental: Waterproof to IPX8 Standard (2 m)
Warranty: 5 years (torch only)
Regulatory Compliance: CE / RoHS


Packaging and Contents

Supplied in retail packaging and contains:
Olight Warrior Mini torch x 1
Olight tailored 18650 3500 mAh 10 A HDC lithium-ion battery x 1
Lanyard x 1
Stainless steel pocket clip x 1
MCC3 USB magnetic charging cable x 1
Manual x 1

Olight Customised 10 A HDC 18650 3500 mAh Li-ion Battery for Baton Pro & Perun

Olight Customised 10 A HDC 18650 3500 mAh Li-ion Battery for Baton Pro & Perun

High Discharge Current of 10 A - Designed for the Olight Baton pro & Perun

Availability:  10+ in stock

This Olight HDC customised 10 A 3.6 V 3500 mAh 18650 battery is designed specifically for the Olight Baton Pro & Perun.

[More details]
£18.95Add to Basket

Olight FB-1 Universal Bike Mount

Olight FB-1 Universal Bike Mount

Fits torches with a diameter of 10-35 mm

Availability:  6 in stock

The Olight FB-1 is a versatile bike mount which enables the fitting of a torch to your bike handlebars. The mount can hold torches with a body diameter of 10-35 mm and fits on handlebars with a diameter of 10-35 mm. Four rubber attachment ring are supplied so you can select the correct size for your torch and handlebars.

Please note: Torch not included.

[More details]
£6.95Add to Basket

Olight MCC3 USB Magnetic Charging Cable

Olight MCC3 USB Magnetic Charging Cable

Compatible with Olight S1R, S1R II, S2R, S2R II, S10R III, S30R III, H2R, M2R, M2R Pro, Seeker 2, Seeker 2 Pro, PL-PRO Valkyrie, Warrior X, Warrior X Pro, Warrior X Turbo and Baton Pro

Availability:  10+ in stock

The Olight USB MCC3 serves as a spare or replacement charging cable for the Olight S1R, S1R II, S2R, S2R II, S10R III, S30R III, H2R, M2R, M2R Pro, Seeker 2, Seeker 2 Pro, PL-PRO Valkyrie, Warrior X, Warrior X Pro, Warrior X Turbo and Baton Pro.

[More details]
£14.95Add to Basket

Be the first to Write a Review for this item!

Receive a great FREE GIFT from Torch Direct

To qualify simply spend over £50 with us, on any one order, minus any delivery fees.
You will then receive an Xtar LED Key Ring Torch completely FREE!

Free gift offer from Torch Direct Ltd

Make it personal with our laser engraving service!

We charge £2.95 per engraving and all you have to do to obtain this service is complete the text form above with the text that you wish to be laser engraved. The text box is located just above the add to basket button, do this before adding your chosen product to your shopping basket.

You can chose to engrave a name, slogan or any text you want.

We are able to reproduce lowercase, uppercase, numbers and punctuation marks, and you may use a maximum of 20 characters per item. Please take great care when typing your chosen text as our system will capture, process, and replicate exactly what has been typed by you. Mistakes cannot be corrected after the engraving has been completed and refunds or exchanges will not be offered.

How do we engrave your product?

We use a top quality fibre laser engraving machine, which provides an accurate beam of laser light to mark your product perfectly and permanently.

Which typeface do we use for engraving and what size is it?

We use a typeface called 'Arial' for all our engraving as we find it gives the best results overall. Depending on which product is being engraved, our machine operators will adjust the text size to fit any available space.

Some samples from our engraving gallery (click to zoom)

If you would like to see more examples then please visit our Engraving Service page.