Olight Warrior Mini 2 Rechargeable LED Torch
Olight Warrior Mini 2 Rechargeable LED TorchOlight Warrior Mini 2 Rechargeable LED TorchOlight Warrior Mini 2 Rechargeable LED Torch
Olight Warrior Mini 2 Rechargeable LED TorchOlight Warrior Mini 2 Rechargeable LED TorchOlight Warrior Mini 2 Rechargeable LED Torch

Olight Warrior Mini 2 Rechargeable LED Torch

Brand:  Olight
Product Code:  OL1047-II-B
maximum allowance of 10 characters

The Olight Warrior Mini 2 is an upgrade on the original, maintaining the dual switches, customised 3500 mAh battery and MMC3 charging cable, but now with new features such as a proximity sensor and carabiner style clip ring.

It features a maximum output of 1750 lumens, before dropping down to 500 lumens after 4 minutes to prevent the LED from overheating. It will run at 500 lumens for 3 hours, 26 minutes before dropping a final time to 200 lumens for 40 minutes.

As well as the active thermal management system that reduces the output when the temperature gets too hot, the Warrior Mini 2 also features a nifty proximity sensor that will automatically reduce the output if the head of the torch becomes too close to an object when it is in the higher settings so that the heat expelled from the torch doesn't cause any damage. If the side button is pressed when close to an object it will turn off the torch, or if the obstruction is there for longer that 60 seconds then the light will turn off.

Utilising a TIR optic lens, the Warrior Mini 2 provides better light quality with a smooth and balanced beam profile. It features the rugged design and dual switches of the M2R Pro combined with the slim compact design and 18650 battery of the Baton Pro, making it the perfect everyday tactical carry.

The included Olight 18650 3500 mAh 10 A high discharge tailored lithium-ion battery is specially designed and only this battery can be charged within the torch. The battery is recharged inside the torch using the included MCC3 magnetic charging cable.

Simply connect the magnet to the base of the torch and plug the USB end into a computer or suitable adaptor. The light on the cable will go red to show charging is in progress and turn green once charging is complete, a full charge takes approximately 3 hours and 30 minutes when using a 5 V 1.5 A input, otherwise charging may be slower.

Featuring five brightness levels and strobe, the torch is turned on and off with a single press of the side mounted push button. Select the brightness level, with the torch turned on, by holding the switch to cycle through low, mid and high in turn, whilst the moonlight mode of 1 lumen can be accessed directly when the torch is off by pressing and holding down the switch, or a single press if it is the last used memorised mode.

Quickly double pressing the side switch will enter and exit turbo mode, while three quick presses with the light on will activate the strobe mode. The memory function will remember the last mode used for moonlight, low, mid and high.

The redesigned tactical tail switch provides stronger magnetism and allows for easier operation while wearing gloves due to the raised button, but without compromising accidental activation thanks to the three raised struts that not only prevent it easily turning on but also allow for tail stand capability. The tail switch will access constant with quick half or full presses, or momentary with a full or half press and hold.

The tactical tail switch is a quiet press button with minimal noise for tactical purposes and can be used in two modes; either configuration 1 or configuration 2. The torch default setting is configuration 1 and to switch to configuration 2 you deep press and hold the tail switch then single press the side switch. In Configuration 1 the tail switch will provide mid output with a half press or turbo output with a full press, and can provide momentary operation by holding down the button either half or fully. Configuration 2 will provide turbo output with a half press or strobe with a full press.

There is a battery level indicator built into the side switch that lets you know when the battery needs charging. A green light indicates above 60% power, a orange light indicates 10% - 60 % power a red light indicates 10% - 5% power and a red flashing light indicates less than 5% power and that the torch needs to be charged.

A handy lockout function prevents the torch from being accidentally activated and is accessed by pressing and holding the switch for 2 seconds to lock it (it will enter moonlight mode first and then lockout) and the same again will unlock it. The Warrior Mini 2 also features a dual purpose magnetic tail cap, so you can use it as a hands-free work light on magnetic surfaces, and attach it securely to the included charging cable.

The innovative two way pocket clip makes it easy to carry the Warrior Mini 2 on clothing, and what's more it comes supplied with a circular carabiner that attaches to the rear tail clip allowing for easy carry on a backpack zip or similar. A lanyard is also included and can only be attached the the slot on the rear tail clip.

Please note: The carabiner is not designed for climbing and is for torch attachment only, and it should be removed when the torch is stowed to prevent it short circuiting on the magnetic tail cap. Ensure the torch is stowed away from magnetic objects and is placed in lockout mode for transport and storage. ALWAYS fully read the manual before use.

Operational Modes

1750 lumens; 4 minutes run-time; 220 m beam range*
500 lumens; 3 hours, 26 minutes run-time
200 lumens; 40 minutes run-time

500 lumens; 3 hours, 38 minutes run-time; 117 m beam range*
200 lumens; 55 minutes run-time

Mid: 120 lumens; 19 hours run-time; 57 m beam range
Low: 15 lumens; 164 hours run-time; 19 m beam range
Moonlight: 1 lumen; 45 days run-time

*The turbo and high setting will decrease to prevent the LED from overheating.

The above results are based on ANSI/NEMA FL1-2009 standard and are tested using the included battery.

Technical Details

Type: EDC hand-held LED torch
Operating Modes: Moonlight / Low / Mid / High / Turbo / Strobe
Luminous Flux: Up to 1750 lumens
Lamp Type: White LED
Lens: TIR reflector
Beam Range: Up to 220 m
Batteries Required: 1 x tailored 3500 mAh 10 A HDC 18650 lithium-ion (included)
Overall Length: 118 mm
Bezel Diameter: 25 mm
Body Diameter: 23 mm
Weight: 122 grams (including battery)
Body Colour: Black or desert tan
Body Material: Aluminium alloy
Body Finish: Type III hard-anodised
Switch Type: Side mounted and tactical tail switch
Impact Resistance: 1.5 m
Environmental: Waterproof to IPX8 Standard (2 m)
Warranty: 5 years (torch only)
Regulatory Compliance: CE / RoHS

Packaging and Contents

Supplied in retail packaging and contains:
Olight Warrior Mini 2 torch x 1
Olight tailored 18650 3500 mAh lithium-ion battery x 1
MCC3 USB magnetic charging cable x 1
Circular carabiner style ring x 1
Two way pocket clip x 1
Lanyard x 1
Manual x 1

Compact USB Charger (2100 mA Output)

Compact USB Charger (2100 mA Output)

28 in stock

This compact USB charger has a power output of 2100 mA, making it ideal for charging many devices that charge via a USB port.

[More details]
£5.95Add to Basket

Olight Customised 10 A HDC 18650 3500 mAh Li-ion Battery

Olight Customised 10 A HDC 18650 3500 mAh Li-ion Battery

High Discharge Current of 10 A - Designed for the Olight Warrior Mini, Baton pro & Perun

25 in stock

This Olight HDC customised 10 A 3.6 V 3500 mAh 18650 battery is designed specifically for the Olight Warrior Mini, Baton Pro & Perun.

[More details]
£18.95Add to Basket

Olight MCC3 USB Magnetic Charging Cable

Olight MCC3 USB Magnetic Charging Cable

Compatible with Olight S1R, S1R II, S2R, S2R II, S10R III, S30R III, H2R, M2R, M2R Pro, Seeker 2, Seeker 2 Pro, PL-PRO Valkyrie, Warrior X, Warrior X Pro, Warrior X Turbo and Baton Pro

10 in stock

The Olight USB MCC3 serves as a spare or replacement charging cable for the Olight S1R, S1R II, S2R, S2R II, S10R III, S30R III, H2R, M2R, M2R Pro, Seeker 2, Seeker 2 Pro, PL-PRO Valkyrie, Warrior X, Warrior X Pro, Warrior X Turbo and Baton Pro.

[More details]
£14.95Add to Basket

Olight FB-1 Universal Bike Mount

Olight FB-1 Universal Bike Mount

Fits torches with a diameter of 10-35 mm

36 in stock

The Olight FB-1 is a versatile bike mount which enables the fitting of a torch to your bike handlebars. The mount can hold torches with a body diameter of 10-35 mm and fits on handlebars with a diameter of 10-35 mm. Four rubber attachment ring are supplied so you can select the correct size for your torch and handlebars.

Please note: Torch not included.

[More details]
£6.95Add to Basket

Olight Warrior Mini 2 Rechargeable LED Torch (Ltd Edition Mountain Sky)

Olight Warrior Mini 2 Rechargeable LED Torch (Ltd Edition Mountain Sky)

1750 Lumens Output - Drops down to 500 lumens after 4 minutes to protect the LED

14 in stock

The Warrior Mini 2 is also available in black and desert tan

This is the Limited Edition Mountain Sky version, available while stocks last.

[More details]
£94.95Add to Basket

Be the first to Write a Review for this item!

Receive a great FREE GIFT from Torch Direct

To qualify simply spend over £75 with us, on any one order, minus any delivery fees.
You will then receive a Mercury FL05C 5 W Cree LED Torch completely FREE!

Free gift offer from Torch Direct Ltd

Make it personal with our laser engraving service!

We charge £3.95 per engraving and all you have to do to obtain this service is complete the text form above with the text that you wish to be laser engraved. The text box is located just above the add to basket button, do this before adding your chosen product to your shopping basket.

You can chose to engrave a name, slogan or any text you want.

We are able to reproduce lowercase, uppercase, numbers and punctuation marks, and you may use a maximum of 20 characters per item. Please take great care when typing your chosen text as our system will capture, process, and replicate exactly what has been typed by you. Mistakes cannot be corrected after the engraving has been completed and refunds or exchanges will not be offered.

How do we engrave your product?

We use a top quality fibre laser engraving machine, which provides an accurate beam of laser light to mark your product perfectly and permanently.

Which typeface do we use for engraving and what size is it?

We use a typeface called 'Arial' for all our engraving as we find it gives the best results overall. Depending on which product is being engraved, our machine operators will adjust the text size to fit any available space.

Some samples from our engraving gallery (click to zoom)

If you would like to see more examples then please visit our Engraving Service page.